Uniflex Acrylic Elastomeric Coating Spec For Metal Roofs

If you believe you'll be saving the roof decking plywood (not replacing it), then you may save yourself some clean-up problem by getting rid of the fixtures initially and after that peeling up the rubber! Detail of water damage on camper roofing. More water damaged areas on Recreational Vehicle roofing decking. There was nothing actually horrible that made me seem like I was going to fail, however certainly a great deal of damage and I was getting the feeling I would be replacing a great deal of the roof decking plywood.

Proper Surface Preparation Is Essential Before Applying Roof

Hop Over To This Site: roofing contractors Tucson AZ - DCRoofingArizona.com http://donovanzzdm052.image-perth.org/2021-roof-coating-sealing-costs

I opted for the easiest one first, a vent cap from a kitchen sink pipes vent pipe. Beginning to scrape caulk and sealant. I utilized a stiff scraper with a chisel-like blade and simply began prying and chipping and scraping and hacking. There is no other method around this, you simply need to begin digging until you expose the screw heads.

Unscrewing the screws in vent cap. The screws on this vent cap were hex-head metal screws so I used a little socket driver to eliminate them. Some came out clean. Others were rusted and I had to utilize a vice-grip pliers to grab the heads and turn them bit by bit.

I found an old wasp nest inside the vent cover. This is a sight I'll most likely need to get used to, discovering the remains of animal habitation in every nook and cranny. I spend a terrible great deal of my time producing great wildlife habitat in my backyard so I don't get upset when an animal chooses to set up home in my Recreational Vehicle.

Elastomeric Coating System Installation Guidelines

Luckily no one was home in this old nest so I just tossed it. Possibly I'll put a screen over it when replacing it. Which brings us to the next point. You must try not to damage these pieces (like vent covers and caps) as you're removing the old caulk and sealant just in case you require to use them once again.

(Think I'll discover when the roofing is done!) Prying up the vent cap and removing the last ring of rubber roof below. So I pried up the remainder of the cap and scraped up the staying rubber roofing system and butyl tape and putty and 25 years of other gunk and here's how it looks tidied up.

Elastomeric Roof Coating & Waterproofing Protection

One down, 7 more fixtures to go. Next I chose to deal with the only roof ventilation fan that my camper has. My roof vent likewise had a vent cover over it. So I started scraping the gunk from those screws. Beginning on the roofing system vent. Hardware exposed on roofing vent cap, the first nut came off clean.

Spraying Elastomerics And Roof Coatings – A Complete Guide

Bolt is spinning. The fasteners on this Recreational Vehicle roofing vent cover were nuts on small bolts. The very first one came off fine with an extension socket package. The second one just began spinning, implying the bolt was not repaired in place however turning along with the nut. Downer. A peek at the hardware holding down the roof vent cover.

What Are Elastomeric Coating And How Are They Used

I didn't have any great way to hold the bolt in place so instead I opted to saw through the bolts with a reciprocating saw. Sawing through bolts on roofing vent cover. I utilized a cordless reciprocating saw with a metal-cutting blade but it was challenging to get the blade flat adequate to reach the bolts so near to the roof deck. Most were so old and rusted that they sheared off when I loosened then with a lot of force. Unscrewing the brackets that held the vent cover in place. Then I scraped more caulk and roof sealant off the flange of the roofing vent itself. I soon found there were no more screws or hardware holding it down so I quit on the scraping and went inside the Recreational Vehicle After scraping the caulk and sealant from flange of roof vent, no more screws! Unscrewing the inside cover plate of roofing vent fan in Recreational Vehicle bathroom.

A couple sheared off with a lot of force, but 2 wouldn't budge. So I had to drill out the screw heads. I chose a drill bit close to the size of the shaft of the screws that I had actually currently pulled out and began drilling. Choosing a drill bit for drilling out a screw head.

Safety glasses suggested. So I drilled out the heads, one popped off and the other I was getting frustrated with and provided it a tug prior to it was drilled through. Instead of popping off the screw head, the plastic just dissolved around the hot screw head. Whoops. Hope I don't need to reuse this cover.

If not, I'll require larger screw heads when re-assembling. Cover plate gotten rid of from roofing system vent. Next I found little corner brackets with hex-head bolts holding them in. I unscrewed them (all came out great thankfully) and pulled out the brackets and little white plastic spacers. Loosening corner brackets in roofing vent.

Elastomeric & Emulsion Roofing

All corner brackets removed, all set to pull out. When the brackets were out I returned up leading to pry out the the roofing system vent. Then I scraped up all the staying gunk and rubber roof. Taking off the old roof vent. There are 2 wires running to the roofing vent (a black hot wire and a white neutral wire) that you'll need to clip to remove the old vent.